 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC489LP5 / 489LP5E v01.0705 SURFACE MOUNT PHEMT 1 WATT POWER AMPLIFIER, 12 - 16 GHz 5 AMPLIFIERS - SMT Typical Applications The HMC489LP5 / HMC489LP5E is ideal for use as a power amplifier for: * Point-to-Point Radios * Point-to-Multi-Point Radios * Test Equipment and Sensors * Military End-Use Features Saturated Power: +32 dBm @ 16% PAE +34 dBm Output IP3 13 dB Gain +7.0 V @ 1300 mA Supply 50 Ohm Matched Input/Output 25 mm2 Leadless SMT Package Functional Diagram General Description The HMC489LP5 & HMC489LP5E are high dynamic range GaAs PHEMT MMIC Power Amplifiers housed in leadless 5 x 5 mm surface mount packages. Operating from 12 to 16 GHz, the amplifier provides 13 dB of gain, +32 dBm of saturated power and 16% PAE from a +7.0 V supply voltage. Output IP3 is +34 dBm typical. The RF I/Os are DC blocked and matched to 50 Ohms for ease of use. The HMC489LP5 & HMC489LP5E eliminate the need for wire bonding, allowing use of surface mount manufacturing techniques. Electrical Specifications, TA = +25 C, Vdd1, 2, 3, 4, 5 = +7V, Idd = 1300 mA* Parameter Frequency Range Gain Gain Variation Over Temperature Input Return Loss Output Return Loss Output Power for 1 dB Compression (P1dB) Saturated Output Power (Psat) Output Third Order Intercept (IP3) Noise Figure Supply Current (Idd)(Vdd = +7V, Vgg = -0.3V Typ.) 24 10 Min. Typ. 12 - 14 13 0.05 12 8 29 30 32 7 1300 28 0.07 10 Max. Min. Typ. 14 - 16 13 0.05 8 15 31 32 34 9 1300 0.07 Max. Units GHz dB dB/ C dB dB dBm dBm dBm dB mA * Adjust Vgg between -2 to 0V to achieve Idd = 1300 mA typical. 5 - 492 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC489LP5 / 489LP5E v01.0705 SURFACE MOUNT PHEMT 1 WATT POWER AMPLIFIER, 12 - 16 GHz Broadband Gain and Return Loss 15 10 5 RESPONSE (dB) 0 -5 -10 -15 -20 -25 8 9 10 11 12 13 14 15 16 17 18 19 FREQUENCY (GHz) S21 S11 S22 Gain vs. Temperature 20 18 16 14 12 10 8 6 4 2 0 -2 -4 -6 11 12 13 14 5 AMPLIFIERS - SMT 5 - 493 GAIN (dB) +25 C +85 C -40 C 15 16 17 FREQUENCY (GHz) Input Return Loss vs. Temperature 0 Output Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) RETURN LOSS (dB) -5 -10 +25 C +85 C -40 C -10 -15 -15 +25 C +85 C -40 C -20 -20 -25 11 12 13 14 15 16 17 FREQUENCY (GHz) -25 11 12 13 14 15 16 17 FREQUENCY (GHz) P1dB vs. Temperature 34 32 30 28 P1dB (dBm) 24 22 20 18 16 14 12 10 11 12 13 14 15 16 17 FREQUENCY (GHz) +25 C +85 C -40 C Psat vs. Temperature 34 32 30 28 Psat (dBm) 26 24 22 20 18 16 14 12 10 11 12 13 14 15 16 17 FREQUENCY (GHz) +25 C +85 C -40 C 26 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC489LP5 / 489LP5E v01.0705 SURFACE MOUNT PHEMT 1 WATT POWER AMPLIFIER, 12 - 16 GHz 5 AMPLIFIERS - SMT Output IP3 vs. Temperature 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 11 12 13 14 Power Compression @ 15 GHz 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0 -8 -4 0 Pout (dBm), GAIN (dB), PAE (%) Pout Gain PAE OIP3 (dBm) +25 C +85 C -40 C 15 16 17 4 8 12 16 20 24 FREQUENCY (GHz) INPUT POWER (dBm) Gain, Power & OIP3 vs. Supply Voltage @ 15 GHz Gain (dB), P1dB (dBm), Psat (dBm), OIP3 (dBm) 36 34 32 30 28 26 24 22 20 18 16 14 12 10 6.5 Gain, Power & OIP3 vs. Supply Current @ 15 GHz Gain (dB), P1dB (dBm), Psat (dBm), OIP3 (dBm) 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 700 Gain P1dB Psat OIP3 Gain P1dB Psat OIP3 7 Vdd Supply Voltage (Vdc) 7.5 800 900 1000 1100 1200 1300 Idd Supply Current (mA) Noise Figure vs. Temperature 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 11 12 13 14 Reverse Isolation vs. Temperature 0 -10 -20 ISOLATION (dB) -30 -40 -50 -60 -70 -80 +25 C +85 C -40 C NOISE FIGURE (dB) +25 C +85 C -40 C 15 16 17 11 12 13 14 15 16 17 FREQUENCY (GHz) FREQUENCY (GHz) 5 - 494 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC489LP5 / 489LP5E v01.0705 SURFACE MOUNT PHEMT 1 WATT POWER AMPLIFIER, 12 - 16 GHz Typical Supply Current vs. Vdd Vdd (Vdc) Max Pdiss @ +85C Power Dissipation* 10.5 10 9.5 9 8.5 14 GHz 8 7.5 7 -10 -8 -6 -4 -2 0 5 AMPLIFIERS - SMT 5 - 495 Idd (mA) 1330 1300 1285 +6.5 +7.0 +7.5 POWER DISSIPATION (W) Note: Amplifier will operate over full voltage ranges shown above. Vgg adjusted to achieve Idd= 1300 mA at +7.0V. Absolute Maximum Ratings Drain Bias Voltage (Vdd1, 2, 3, 4, 5) Gate Bias Voltage (Vgg) 2 4 6 8 10 12 14 16 18 20 22 24 +8 Vdc -2.0 to 0 Vdc +28 dBm 150 C 10 W 6.5 C/W -65 to +150 C -40 to +85 C RF Input Power (RFin)(Vdd = +7.0 Vdc) Channel Temperature INPUT POWER (dBm) * Refer to "Thermal Management for Surface Mount Components" application note herein. Continuous Pdiss (T= 85 C) (derate 154 mW/C above 85 C) Thermal Resistance (channel to ground paddle) Storage Temperature Operating Temperature ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC489LP5 HMC489LP5E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H489 XXXX H489 XXXX [2] [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC489LP5 / 489LP5E v01.0705 SURFACE MOUNT PHEMT 1 WATT POWER AMPLIFIER, 12 - 16 GHz 5 AMPLIFIERS - SMT Pin Descriptions Pin Number 1-3, 5-8, 10-12, 14, 15, 17-20, 22-24, 26, 27, 29-31 4 Function N/C Description No connection required. These pins may be connected to RF/DC ground without affecting performance. This pin is AC coupled and matched to 50 Ohms from 12 - 16 GHz. Interface Schematic RFIN 9 Vgg Gate control for amplifier. Adjust to achieve Idd of 1300 mA. Please follow "MMIC Amplifier Biasing Procedure" Application Note. External bypass capacitors of 100 pF and 2.2 F are required. 21 RFOUT This pin is AC coupled and matched to 50 Ohms from 12 - 16 GHz. 32, 28, 25, 13, 16 Vdd1, Vdd2, Vdd3, Vdd4, Vdd5 Power Supply Voltage for the amplifier. External bypass capacitors of 100 pF and 2.2 F are required. GND Ground: Backside of package has exposed metal ground slug that must be connected to ground through a short path. Vias under the device are required Application Circuit Component C1 C2 Value 100 pF 2.2 F 5 - 496 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC489LP5 / 489LP5E v01.0705 SURFACE MOUNT PHEMT 1 WATT POWER AMPLIFIER, 12 - 16 GHz Evaluation PCB 5 AMPLIFIERS - SMT List of Materials for Evaluation PCB 108190 [1] Item J1, J2 J3, J4 C1 - C6 C7 - C12 U1 PCB [2] Description SRI PC Mount SMA Connector 2mm DC Header 100 pF capacitor, 0402 pkg. 2.2F Capacitor, Tantalum HMC489LP5 / HMC489LP5E Amplifier 108188 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350. The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. Copper filled vias under the device are recommended. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 497 |
Price & Availability of HMC489LP5E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |